HILWAY DIRECT

Floor Cleaning & Maintenance Products

Hilway Direct
12 McCullough Dr, Suite 10
New Castle, DE 19720
United States

ph: 877-356-6748

support@hilway.com

  • Home
  • Cleaners - FinishesClick to open the Cleaners - Finishes menu
    • PRIMO HP
    • PRIMO GLOSS
    • PLUS
    • PLUS MATTE
    • PLUS GLOSS
    • MATTE
    • SATIN
    • NEUTRAL CLEANER
    • ALLSAFE STRIPPER
  • SUPPLIESClick to open the SUPPLIES menu
    • SPRAY MOP
    • MOLDING TAPE
  • Library
  • Videos

Hilway Direct PLUS

33.8 Ounces (1 Liter) Item No. HD-P1L  

1.33 Gallon (5 Liter) Item No. HD-P133

5 Gallon Item No. HD-PLUS5G

  • PLUS Floor Finish & Cleaner/Maintainer

    HD Plus MatteHilway Direct PLUS Floor Finish & Cleaner/Maintainer, 33.8 Ounces (1 Liter) \ 1.33 Gallon (5 Liter) \ 5 Gallon.

    Low-sheen acrylic finish with integrated cleaner/maintainer. Durable, wear-resistant coating. High solids (30% solids) acrylic finish. Use as finish alone or as one-step clean-maintain.

    • Excellent Wear & Scuff Resistance
    • Low-sheen Acrylic Finish    
    • All-in-one Protective Coating & Cleaner Maintainer
    • Reduced strip & polish Cycles 
    • No VOCs                              
    • No Yellowing


    For Use On:  Sheet Vinyl, VCT, Cork, Rubber, Linoleum, LVT, Slate, Concrete, Quarry Tile, Marble, Terrazzo, Asphalt Tile

    Initial Application Directions:  Sweep then damp mop floor. Thoroughly clean floor or remove existing finish (factory or site applied) with properly diluted floor cleaner or finish remover such as Hilway Direct Neutral Cleaner or AllSafe Stripper. Rinse floor thoroughly with clean water to neutralize after stripping floor. Do not let stripper solution dry on floor. Shake Hilway Direct Plus vigorously for 30 seconds then let it settle for 5 minutes. Apply undiluted in a thin, even coat using a microfiber applicator mop. Apply 2-3 coats. Allow each coat to air dry completely (generally 30-60 minutes) before applying next coat. Allow floor surface to dry overnight before heavy traffic use.

    Initial Application Coverage, single coat (undiluted): 350 square feet/ liter; 1500 – 2000 square feet/ 1.33 gallons.  Coverage may vary depending on porosity of flooring material.

    Daily Cleaning, Mop & Bucket Directions:
    Sweep floor. Dilute 1 oz of Hilway Direct Plus per 1 gallon warm water.  Mop floor with solution using a 2-bucket system. Pick up soil and excess solution with a clean, tightly wrung out mop.  No rinsing required.  Allow to air dry.

    Daily Cleaning, Auto Scrubbing Machine Directions:
    Dilute 1 oz of Hilway Direct Plus per 1 gallon warm water. Scrub floor with solution. Trail mop excessive wet areas behind scrubber. No rinsing required. Allow floor to air dry. 

    Caution:  Eye irritant. Avoid contact with skin and eyes. Do not taste or swallow. In case of contact with eyes or skin flush with plenty of water. If irritation develops, seek medical attention. In case of ingestion, flush mouth with water, drink large quantities of water and seek immediate medical attention, DO NOT induce vomiting. Keep out of reach of children.

    Note:  Avoid solution contact with sensitive surfaces such as wood, metal, furnishings.  When applying finish, avoid strong sunlight and drafts. Turn off under floor heat prior to application. Read full MSDS (available for download) and product label prior to use.

    Handling and Storage:
      Protect from freezing. Recommended storage temperature: 68°F (20°C).  Avoid storing in direct sunlight and high temperatures. Do not store near food.

    Downloads:     Safety Data Sheet,  Product Information,  Instructions for Use

Copyright 2019 Hilway Direct. All rights reserved.

Web Hosting by Yahoo!

Hilway Direct
12 McCullough Dr, Suite 10
New Castle, DE 19720
United States

ph: 877-356-6748

support@hilway.com