HILWAY DIRECT

Floor Cleaning & Maintenance Products

Hilway Direct
12 McCullough Dr, Suite 10
New Castle, DE 19720
United States

ph: 877-356-6748

support@hilway.com

  • Home
  • Cleaners - FinishesClick to open the Cleaners - Finishes menu
    • PRIMO HP
    • PRIMO GLOSS
    • PLUS
    • PLUS MATTE
    • PLUS GLOSS
    • MATTE
    • SATIN
    • NEUTRAL CLEANER
    • ALLSAFE STRIPPER
  • SUPPLIESClick to open the SUPPLIES menu
    • SPRAY MOP
    • MOLDING TAPE
  • Library
  • Videos

Hilway Direct PRIMO HP

33.8 Ounces (1 Liter) Item No. HD-PRM1L 

1.33 Gallon (5 Liter) Item No. HD-PRM133

  •  PRIMO HP Polyurethane-Acrylic Floor Finish

    HD Primo HPHilway Direct PRIMO HP Floor Finish, 33.8 Ounces (1 Liter) \ 1.33 Gallon (5 Liter)

    Extremely hard-wearing acrylic modified polyurethane finish intended for use in high traffic areas. Use on resilient and hard surface floors. 

              • High Solids Content (42%) for optimal performance in High Traffic areas.
              • Excellent Wear & Scuff Resistance
              • Low-sheen minimizes the appearance of scratches.
              • Non-hazardous, no VOCs.


    For Use On:  Sheet Vinyl, LVT, VCT, Rubber, Linoleum, Cork, Asphalt Tile, Marble, Slate, Concrete, Quarry Tile, or Terrazzo Flooring.

    Application Directions:  Sweep then damp mop floor. Thoroughly clean floor with Hilway Direct Neutral Cleaner or Allsafe Stripper, diluted according to label insructions, or use flooring manufacturer’s recommended product.  If flooring has a factory or site-applied acrylic coating, remove coating following flooring manufacturer’s instructions. This usually can be done with Hilway Direct Allsafe Stripper diluted 1:5 or 1:10 with clean water, or flooring manufacturer’s recommended product diluted as directed, in an auto scrubber or low rpm swing machine with a red pad or equivalent.  Always rinse floor with clean water after removing old coating to completely neutralize floor. Do not let stripper solution dry on floor.  Shake Hilway Direct Primo HP vigorously for 30 seconds then let it settle for 5 minutes.  Apply undiluted in a thin, even coat using a microfiber applicator mop. Do not use treated dust mops. Allow first coat to air dry completely (approximately 1 hour) then apply second coat in crosswise direction.  Allow floor surface to dry minimum of 12 hours before heavy traffic use.

    Initial Application Coverage, single coat (undiluted): 350 square feet/ liter; 1500 – 2000 square feet/ 1.33 gallons.  Coverage may vary depending on porosity of flooring material.

    Daily Cleaning Directions:  Sweep floor to remove loose dirt & soil.  Using Mop & Bucket (2-bucket system) or Auto-Scrub Machine, dilute Hilway Direct Neutral Cleaner as directed on product label.  Mop floor with the cleaning solution.  Trail mop excess soil and wet areas with a clean, tightly wrung out mop.  No rinsing required.  Allow floor to air dry completely.

    Caution:  Eye irritant. Avoid contact with skin and eyes. Do not taste or swallow. In case of contact with eyes or skin flush with plenty of water. If irritation develops, seek medical attention. In case of ingestion, flush mouth with water, drink large quantities of water and seek immediate medical attention, DO NOT induce vomiting. Keep out of reach of children.

    Note:  Avoid solution contact with sensitive surfaces such as wood, metal, furnishings.  When applying finish, avoid strong sunlight and drafts. Turn off under floor heat prior to application. Read full MSDS and product label prior to use.

    Handling and Storage:  Protect from freezing. Recommended storage temperature: 68°F (20°C).  Avoid storing in direct sunlight and high temperatures. Do not store near food.

    Downloads:      Safety Data Sheet,   Product Information,  Instructions for Use


Copyright 2019 Hilway Direct. All rights reserved.

Web Hosting by Yahoo!

Hilway Direct
12 McCullough Dr, Suite 10
New Castle, DE 19720
United States

ph: 877-356-6748

support@hilway.com